密度泛函理论方法研究填料表面对聚合物摩擦化学的影响

采用超声分散法制备出氧化铝、高岭土、氧化硅/聚四氟乙烯复合材料, 使用线性往复摩擦磨损试验机对比三种复合材料的摩擦学性能. 结果表明 质量分数10%的氧化铝、高岭土能将聚四氟乙烯的磨损率降低约4个数量级, 而氧化硅仅能降低约3个数量级. 对金属对偶表面形成的转移膜的形貌和化学成分进行分析发现 氧化铝、高岭土/聚四氟乙烯在金属对偶面上形成了高度羧酸盐化的转移膜. 用密度泛函理论对三种填料表面上碳氟分子吸附过程进行模拟, 结果显示氧化铝、高岭土表面的路易斯酸性位点促进了碳氟分子的脱氟过程, 产生了更多的羧酸螯合物的中间产物; 氧化硅缺少路易斯酸性位点, 因此不能促进高度羧酸盐化的转移膜形成.     

气相输运沉积制备c轴择优取向的碘化铋薄膜

铋基卤化物材料因其无毒和优良的光电性能而显示出巨大的应用潜力。BiI₃作为一种层状重金属半导体,已被用于X射线检测、γ射线检测和压力传感器等领域,最近其作为一种薄膜太阳能电池吸收材料备受关注。本文采用简单的气相输运沉积(VTD)法,以BiI₃晶体粉末作为蒸发源,在玻璃基底上得到高质量c轴择优取向的BiI₃薄膜。并通过研究蒸发源温度和沉积距离对薄膜物相和形貌的影响,分析了BiI₃薄膜择优生长的机理。结果表明VTD法制备的BiI₃薄膜属于三斜晶系,其光学带隙为~1.8 eV。沉积温度对薄膜的择优取向有较大影响,在沉积温度低于270 ℃时,沉积的薄膜具有沿c轴择优取向生长的特点,超过此温度,c轴择优取向生长消失。在衬底温度为250 ℃、沉积距离为15 cm时制备的薄膜结晶性能最好,晶体形貌为片状八面体。     

Calcium-based coordination polymers from a solvothermal synthesis of HKUST-1 in 3D printed autoclaves

A mixed-metal 1D coordination polymer [CaCu(HBTC)₂(H2O)₈]_n (where H₃BTC – benzene-1,3,5-tric arboxylic acid) was obtained in a solvothermal synthesis of a well-known copper-containing metal–organic framework [Cu₃(BTC)₂(H₂O)₃]_n (HKUST-1) in autoclaves 3D-printed from commercial polypropylene. This material was a source of calcium ions, apparently, leaking from a colorant (calcium carbonate) promoted by glacial acetic acid as a modulator used to produce large single crystals of HKUST-1. This finding was confirmed by elemental analysis and a model experiment that resulted in a new calcium-based 1D coordination polymer [Ca(H₂BTC)₂(H₂O)₅]_n under the same solvothermal conditions with no copper or calcium salts put into a 3D-printed autoclave.     

非富勒烯受体DA'D型稠环单元的结构修饰及电池性能研究

近年来,设计和合成高性能非富勒烯受体(NFAs)材料已经成为太阳能电池研究领域的前沿课题。基于DA'D型稠环结构的NFAs由于具有吸光系数高、能级和带隙可调、结构易于修饰、分子可高效合成、光电学性能优异等优点而受到了越来越广泛的关注。在短短7年的时间里,能量转换效率(PCE)从3%~4%提高到18%。2019年初邹应萍等报道了一个优秀的受体分子Y6,与PM6共混制备单结电池,获得了15.7%的能量转换效率。Y6类受体材料的中心给电子单元为DA'D型稠环结构,缺电子单元(A')通过氮原子与两个给电子单元(D)并联形成稠环结构,这有助于降低前线分子轨道能级并增强吸收,同时与氮相连的两个烷基链和位于噻吩并噻吩β位的两个侧链则有助于提高溶解度及调节结晶性。自Y6问世以来,人们对分子的结构剪裁进行了深入的研究,并报道了数十种新的结构。在这些新的受体中,DA'D部分的结构裁剪对提高器件效率和太阳能电池的性能起着至关重要的作用。本文对A'、D单元和侧链结构修饰的研究进展进行了综述。通过选择几组受体,对最近报道的分子进行分类,并将它们的光学、电化学、电学和光电性质与精确的结构修饰相关联,从而对结构-性能关系进行全面概述。     

Visible light-driven acridone catalysis for atom transfer radical polymerization

Acridone as a new kind of visible light photocatalyst has been developed to catalyze metal free atom transfer radical polymerization (ATRP). The photocatalyst possess low excited state potential as can undergo an oxidative quenching pathway to initiate ATRP of vinyl monomers. Kinetic study and light on/off reaction demonstrate the “living”/controlled nature of the polymerization by light. Block copolymers can be achieved by using PMMA as macroinitiator to reinitiate polymerization of other vinyl monomers, which shows highly preserved Br chain-end functionality in the synthesized polymers. Moreover, the polymerization can be conducted under air atmosphere as most photocatalysts need anaerobic condition, which may give inspiration of further application of this kind of photocatalyst.     

Chemistry of Pentafluorosulfanyl Derivatives and Related Analogs: From Synthesis to Applications

Pentafluorosulfanyl (SF₅)-containing compounds and corresponding analogs are a highly valuable class of fluorine-containing building blocks owing to their unique properties. The reason for that is the set of peculiar and tremendously beneficial characteristics they can impart on molecules once introduced onto them. Despite this, their application in distinct scientific fields remains modest, given the extremely harsh reaction conditions needed to access such compounds. The recent synthetic approaches via S−F, and C−SF₅ bond formation as well as the use of SF₅-containing building blocks embody a “stairway-to-heaven” loophole in the synthesis of otherwise-inaccessible chemical scaffolds only a few years ago. Herein, we report and evaluate the properties of the SF₅ group and analogs, by summarizing synthetic methodologies available to access them as well as following applications in material science and medicinal chemistry since 2015.     

Circularly polarized luminescence based on small organic fluorophores

Circularly polarized luminescence (CPL) has attracted attention as a next-generation light signal because of its carrying more information compared with normal and linearly polarized lights as well as its potential wide application in information fields. Recently, much attention has been paid to small organic molecules-based CPL emitters because of easy synthesis, fine structural modification at molecular level, and tunable wide range emission wavelength. This review highlights the development of small organic molecules-based CPL emitters in the past 5 years (2017–2021). The progress suggests that small organic molecules-based CPL emitters provide a simple and efficient way to generate CPL.     

基于抛光基材的热蒸镀铜箔生长高平整单层石墨烯薄膜

在石墨烯的化学气相沉积工艺中,铜箔是决定石墨烯薄膜质量的重要因素。传统铜箔由于制备工艺的限制,存在大量的缺陷,导致石墨烯薄膜的成核密度较高。本工作选用抛光铝板、抛光不锈钢板、微晶玻璃和SiO₂/Si作为基材,用热蒸镀法制备了不同粗糙度的铜箔,并详细讨论了以该系列铜箔生长高平整度石墨烯薄膜的条件及铜箔对石墨烯薄膜品质的影响。实验结果表明,铜箔以(111)取向为主,与基材分离后,表面具有纳米级平整度。在生长石墨烯后,从SiO₂/Si剥离的铜箔成核密度是4种基材中最小的。同时,从SiO₂/Si剥离的铜箔晶体结构变化最不明显,具有良好的结晶性,表面几乎不存在铜晶界缺陷。当压强为3 000 Pa,氢气和甲烷流速分别为300 mL/min和0.5 mL/min时,可以获得约1 mm横向尺寸的石墨烯单晶晶畴。     

有机张力半导体及其光电特性

分子张力作为空间设计的重要组成部分正成为调控有机半导体的重要手段。由于分子内产生的拉伸张力、扭曲/弯曲张力以及空间张力而导致p轨道排布重组和构型构象结构发生变化,最近各种几何与拓扑结构的高张力有机半导体材料相继被报道,这使得高张力有机半导体材料成为有机电子领域研究的焦点。为了进一步梳理分子张力在有机半导体材料中扮演的角色与价值,该综述从分子张力的类型、实验与理论量化以及可视化出发,总结了高张力共轭芳烃的分子设计策略、与其光电性能分子张力之间的关系,以及这类新兴材料在光电领域的应用。最后,对高张力共轭芳烃的研究前景进行了展望,阐述了该类材料所面临的机遇与挑战。     

Systematic Modulation of Thiol Functionalities in Inexpensive Porous Polymers for Effective Mercury Removal

Through accumulation, mercury contamination in aquatic systems still poses serious health risks despite the strict regulations on drinking water and industrial discharge. One effective strategy against this is adsorptive removal, in which a suitably functionalized porous material is added to water treatment protocols. Thiol (SH) group-grafted structures perform commendably; however, insufficient attention is paid to the cost, scalability, and reusability or how the arrangement of sulfur atoms could affect the Hg^II binding strength. We used an inexpensive and scalable porous covalent organic polymer (COP-130) to systematically introduce thiol functional groups with precise chain lengths and sulfur content. Thiol-functionalized COP-130 demonstrates enhanced wettability and excellent Hg^II uptake of up to 936 mg g⁻¹, with fast kinetics and exceptionally high selectivity. These Hg adsorbents are easily regenerated with HCl and can be used at least six times without loss of capacity even after treatment with strong acid, a rare performance in the domain of Hg-removal research.